Sanyo POA-MD13NET2 Instrukcja Użytkownika Pobierz pdf (Strona 60)

Chapter 5 Controlling the Multi-Projectors

Control multi-projectors at the same time

The valid controls are shown below. Please refer to chapter 4 “Controlling the

Projector” (☞ p.35) for further control and description. When the control button or

setting button is pressed, the registered projectors for the multi-control are controlled

at the same time.

* These control items differ from each selected input mode and functions

of the projector you use. Change of function is disable if the multi-controlled projector does not

support its function.

* The above pages are example. They may differ

from the actual depending on the projector's

model type.

1 2 ... 55 56 57 58 59 60 61 62 63 64 65 ... 91 92

POA-MD13NET2 1
Compliance 2
Contents 3
Chapter 1 5
Preparation 5
Features 6
Internet 7
Intranet 7
Operating Environment 8
Computer 9
The limitation* 9
Expression/Abbreviation 10
Use of this manual 10
Trademark 10
Chapter 2 11
Installation 11
Flow of installation 12
Caution 13
2 Remove 2 screws on a board 14
1 Turn the Mains switch off 14
(10Base-T, 100Base-TX) 15
UTP straight cable 15
Projector 15
Mains Switch 15
1 Selection of network menu 16
3 Restart the Network board 17
Network PIN code setting 18
10-key pallet 19
Network configuration (Type2) 20
Password 22
Network Board 23
Chapter 2 Installation 24
Chapter 3 25
Basic Setting and Operation 25
1 Enter the IP address 26
Display of main setting page 27
Initial Settings 29
2 Password Setting 30
3 Date/Time Setting 30
Network Configuration 31
E-mail Setting 32
E-Mail Setting 33
Chapter 4 35
Controlling the Projector 35
Power on/off the projector 36
Check the status of projector 37
Control the projector 38
PC Adjustment 39
Load a Set 40
Save a Set 40
System Adjustment 41
Image Adjustment 42
Save a image adjustment value 43
Load a image mode 43
Sound Adjustment 44
Screen Adjustment 44
Control the Projector 45
About Lamp Counter reset 46
1 Set a day or date 48
2 Set a time 48
4 Register an event 48
Getting the current time 49
Cancel the timer 49
1 Adjust and set the controls 51
2 Select the Save page 51
3 Name the current setting 51
4 Save the current setting 51
Load a control set 52
Control the projector’s menu 53
Make a memo 54
Chapter 5 55
Multi-Control 56
OWNER’S MANUAL 57
IP address 57
Projector name 57
Chapter 6 61
Use of Serial Port 61
Serial Port setting 62
RS-232C serial cable 64
Use of Telnet 66
Chapter 6 Use of Serial Port 68
* Use the IP address 68
Command list table 68
Chapter 7 69
Appendix:A 69
Examples of Connection 70
Examples of connection 71
To another network 71
Web browser setting 72
Examples: OS/Browsers 73
Proxy setting 74
Netscape Navigator v.7.0 75
JavaScript Setting 75
Mac OS 8.6 77
Netscape Navigator v.4.7 79
Product specification 81
Port Specification 82
Appendix:B 83
Installation/Access 84
Chapter 7 Appendix 86
IDRMD (built in KJ5AL) (b) 92

Komentarze do niniejszej Instrukcji

Brak uwag

Sanyo POA-MD13NET2 Instrukcja Użytkownika Strona 60

Komentarze do niniejszej Instrukcji

Powiązane produkty i podręczniki dla Projektory Sanyo POA-MD13NET2