Sanyo LNS-T33 Instrukcja Obsługi Pobierz pdf

Following checks and confirmations should be taken for safety.

Check the following things by the time of the cabinet mount after the lens replacement.

1. Check the lens is securely fixed.

2. Check the proper wiring and the wires are fixed properly.

3. Check each connector is connected properly.

4. Check no wiring is tangled on the gear of lens motor or the other mechanical parts.

5. Check no parts is missing, or no mounting part is loose.

LCD PROJECTOR LENS

MODEL LNS-T33

LENS REPLACEMENT PROCEDURE

Lens replacement should be performed by the qualified service personnel.

It should be followed by this procedure precisely.

Before attempt to replace the lens, confirm the model number (both the

LCD projector and the lens) and use the proper lens.

The lens cover is on the lens for protection. Be sure to remove the lens

cover before installation.

When installing or removing the lens, be careful not to stain, scratch or

damage the lens.

When shipping the projector with the lens, remove the lens before shipping

the projector.

If you have any questions, contact the dealers.

Following parts are contained in the packing.

1AA6P1P5722-- (IFRD)

PARTS LIST

● LENS

● SCREW DRIVER (3 mm, Green)

● SCREW DRIVER (4 mm, Yellow)

● LIGHT-BLOCK SHEET

● SPACER

● CABLE TIE

1 piece

1 piece (Part No. 910 287 7329)

1 piece (Part No. 910 275 6020)

1 piece Type PJ1 (Part No. 610 347 3901)

1set (Part No. 610 301 6658)

2 pieces (Part No. 645 004 5387)

NOTE; Lens installation is different in cabinet design (Type A and B). Before installation

the lens, check cabinet design.

Some parts are not used for installation or replacement. Keep these parts and

drivers included in the lens for later use.

Printed in Japan

Notes on Lens Replacement

●

1 2 3 4 5 6 7 8

Podsumowanie treści

Strona 1 - LENS REPLACEMENT PROCEDURE

Following checks and confirmations should be taken for safety.Check the following things by the time of the cabinet mount after the lens replacement.1

Strona 2

Turn the lens cover to counter-clockwise and pull it toward front and remove the lens cover.Remove 2 screws-A.Remove the front cabinetREMOV E THE LE

Strona 3

- 3 -3REMOVE THE LENSGrasp the lens lock lever and turn it fully upward. Remove the lens into the projector.Disconnect the lens motor lead connec

Strona 4 - LENS LOCK LEVER

- 4 -Grasp the lens lock lever and turn it fully upward. Install the lens into the projector. Turn the lens lock lever fully downward until lever is l

Strona 5

- 5 -5MOUNT THE LIGHT-BLOCK SHEET AND LIGHT-BLOCK SHEET BASE6MOUNT THE FRONT CABINETMount the light-block sheet (PJ1) on the lens. (In the

Strona 6 - Pull the lens

- 6 -While pressing the top cover release button on the top cover, slide the top cover toward front to remove it.REMOVE THE TOP COVER1

Strona 7 - Push the lens

- 7 -4MOUNT THE LENSRemove protective caps (front and back) on the optional lens.Mount the lens on the lens attachment with 4 screws.1.2.Connect the l

Strona 8 - Correcting the focus

- 8 -When the lens is attached to the projector and images are being projected onto the screen, the peripheral focus may be out of focus in so

Komentarze do niniejszej Instrukcji

Brak uwag

Sanyo LNS-T33 Instrukcja Obsługi

Przeglądaj online lub pobierz Instrukcja Obsługi dla Soczewki projekcyjne Sanyo LNS-T33. Sanyo LNS-T33 Instrukcja obsługi

Podsumowanie treści

Komentarze do niniejszej Instrukcji